Group
Contact Us
Tel.: 0086-13910819265
Mobile: 0086-10-61763316-210
E-mail: [email protected]
Address: Room 1-6, Building 2, Hongfu Science Park, BeiQiJia Town, Changping District, Beijing, China
Factory Address: Xiangtian Industrial Park, San Zhua Lun Street, Jingan County, Yichun City, Jiangxi Province 330600, China

Structure and technical parameters of BT-150HG PCD tool grinder


2019-08-19


Normal operation and use of BT-150HG PCD tool grinder

The main components of the BT-150HG PCD tool grinder. The inner grinding tool 4 is used to support the grinding wheel spindle of the grinding inner hole. And the inner grinding tool spindle is driven by a separate motor. The grinding wheel frame 5 is used to support and drive the grinding wheel spindle rotating at high speed. The wheel frame is mounted on the sliding saddle 6. When the short conical surface needs to ground. The wheel frame can adjust to a certain angular position in the horizontal plane (±30°. The tailstock 7 and the head frame 2 together support the workpiece.

Saddle and lateral the feeding mechanism rotates the lateral feeding handwheel 9 to enable the lateral feeding mechanism to drive the sliding saddle 6 and the grinding wheel frame thereon for the lateral feeding movement. The working table 3 is composed of two upper and lower layers. The upper working table can use to workaround. The angle of the table is rotated by an angle (±10°) to grind a long conical surface with a small taper. The top of the workbench on the Precision BT-150HG PCD tool grinder is equipped with a headstock 2 and a tailstock 7. Which can use with together with the workbench, make a longitudinal reciprocating motion along the guide rail of the bed.

The main characteristic of BT-150HG PCD tool grinder

The main characteristic of the tool grinder in the process of use is that the cutting force is relatively small. So it is necessary to effectively improve the grinding force of the tool. In the process of inspection, they first need to check the spindle of the grinding wheel frame and then adjust the gap of the bearing bush. This can effectively ensure that the data does not have errors in the data during use. BT-150HG PCD tool grinder the oil on the spindle of the upper wheel frame also needs to replace. If it is working for a long time, if the oil of the main machine is not replaced in time. It will directly affect the operation of the equipment.

In the process of using the tool grinder, the oil leakage must not occur. The guide rail of the working table of the equipment also needs to check regularly. If there is a problem, it needs to check in time, and then it is carried out with its sophisticated technology.  In the process of use, the precision function of the government equipment can effectively report to not damaged. In the use, the headstock and the tail of the equipment should inspect regularly. If there is a fault in the equipment, precision maintenance is required. In order to ensure the normal operation and use of the precision BT-150HG PCD tool grinder device.

Overall reasonable structure and processing characteristics of the PCD tool analyzer

Check PCD tool analyzer. Whether the rotation condition is normal, whether the fixture is in contact with the machine tool pin. Stop the spindle to check whether it is convenient and quick to remove the workpiece. Adjust the machine tool, adjust the appropriate tailstock position according to the shape length of the workpiece, and press the tailstock. Retract the grinding wheel a certain distance, install the workpiece, open the spindle, and rotate the workpiece.

Structure and technical parameters of BT-150HG PCD tool grinder

BT-150HG PCD tool grinder workpiece is not centered and supported but placed between the grinding wheel and the guide wheel, pallet, and the guide wheel support it. The grinding wheel is usually installed at the end of the spindle, and the grinding wheel with a width of more than 250 mm is mounted on the spindle. In the middle, the grinding wheel has a width of up to 900 mm. The grinding wheel rotates at high speed for grinding, and the guide wheel rotates in the same direction at a slower speed, which drives the workpiece to rotate for circumferential feeding. Through the grinding, the slight inclination angle of the guide wheel axis is adjusted.

Achieve axial feed, suitable for grinding slender cylindrical workpieces, short shafts without shaft holes and sleeve-like workpieces, etc. When cutting into the grinding, radial feed is realized by the movement of the guide wheel frame or the grinding wheel frame. Suitable for grinding the shoulder Or the workpiece of the boss, as well as the cone, sphere or other plain line is the workpiece of the curve.

Precision BT-150HG PCD tool grinder spindle to working surface distance: 350-400mm (13.8-15.7″). Maximum grinding length: 510mm (20″) spindle to working surface distance. 350-400mm (13.8-15.7″) standard disk size : 200 × 450mm (6 × 18″). Left and right feed / manual stroke: 485mm (19″). Front and rear feed / manual stroke: 180mm (7″). Front and rear handwheel feed per scale: 0.02mm (0.01″) . Before and after Handwheel per revolution: 5mm (0.2″) lift feed / handwheel feed per scale: 0.005mm.

Beijing Demina Precision Machinery CO., LTD a professional BT-150HG PCD tool grinder manufacturer. Now all kinds of tool grinding machines are available for sale, welcome to visit and purchase.

Learn More Information About Our Products Know More
  • BEIJING DEMINA PRECISION MACHINERY CO., LTD.

    [JIANGXI GEQI GRINDING TECHNOLOGY CO., LTD.]

    Address:
    Room 1-6, Building 2, Hongfu Science Park, BeiQiJia Town, Changping District, Beijing, China
    Factory Address:
    Xiangtian Industrial Park, San Zhua Lun Street, Jingan County, Yichun City, Jiangxi Province 330600, China
    Contact: Zhiyong Shu Mobile:0086-13910819265
    Fax: 0086-10-61763316-210 E-mail: [email protected]
    Tel-Nub: 0086-10-62965622 0086-13910819265

  • Inquiry Now

    *Name:
    *E-mail:
Copyright © BEIJING DEMINA PRECISION MACHINERY CO., LTD All Rights Reserved.